Cummins Diesel
Dodge Diesel Chips & Dodge Diesel Performance Parts Increase Dodge Cummins Diesel Engine Performance...
ONLY the 6.7 Liter Requires Shims:
Installation Page:
For 6.7 liter ONLY ! - 
Three ( 3 ) Washers
Three ( 3 ) Washers and Separation Tool
Shim Kit / For 6.7 Liter Dodge
Cummins Diesel Engine Fuel Rail Valve

1. Remove the dipstick and 4 bolts holding the plastic cover plate on top of the dodge cummins diesel engine.
2. Using an 11mm wrench remove the 2 clamps holding the EGR tube that crosses in front of the dodge cummins diesel engine valve cover. You do not have to remove the dodge cummins diesel engine tube only tilt the dodge cummins diesel engine tube up towards the front of the dodge cummins diesel engine truck.

3. Using a 10mm socket and wrench, remove the dodge cummins diesel engine bolt that holds the dodge cummins diesel engine dipstick tube to the dodge cummins diesel engine bracket and the dodge cummins diesel engine 6 bolts that hold the dodge cummins diesel engine air horn to the dodge cummins diesel engine manifold. Making sure not to damage the dodge cummins diesel engine gasket, slide the dodge cummins diesel engine air horn forward so that you can access the front of the dodge cummins diesel engine fuel rail.
4. Remove the dodge cummins diesel engine 18mm fuel rail valve located on the front of the dodge cummins diesel engine fuel rail.
5. Take dodge cummins diesel engine valve and thread supplied nut tool onto dodge cummins diesel engine valve. Then place dodge cummins diesel engine valve in a vice, clamping down on sides of dodge cummins diesel engine valve cap.
6. Use a wrench to unscrew supplied nut in order to remove dodge cummins diesel engine valve cap. Be careful to hold end of dodge cummins diesel engine valve while doing this! It is spring loaded and you don't want to loose dodge cummins diesel engine parts!
7. Removing metal spring, then insert the 3 supplied metal shims into valve.
8. Replace valve spring and then cap. Note that there are 3 holes in a triangle position on the inside of the valve cap that does not need to be removed from cap and should face towards spring as it did when it was removed, hole alignment is not necessary.
9. Place valve back in vice, now with a thick piece of cardboard or piece of wood behind valve cap to prevent damage to the valve seal surface. Tighten vice so that the valve cap reenters valve until fully seated. No need to over-tighten; just tighten until snug.
10. Take a small punch and small hammer and re-apply the 3 factory indentations along the lip where the valve casing covers the valve cap. You may need to loosen the vice slightly to rotate the valve to access all 3 indentations, but do not let the spring push the cap out any! Make sure that the cap stays fully seated in valve while rotating. After doing so loosen the vice and make sure that the valve cap is held by the indentations.
11. Re-install the dodge cummins diesel engine fuel valve and tighten it down to 50 ft. lbs.
12. Now you can re-install the dodge cummins diesel engine air horn, make sure to line up the six holes in the gasket with the dodge cummins diesel engine bolt holes for the dodge cummins diesel engine air horn. Also connect the dodge cummins diesel engine dipstick tube to the dodge cummins diesel engine bracket on the dodge cummins diesel engine air horn.
13. Line the dodge cummins diesel engine EGR tube back up. For easier installation line up one side to its connection, install the dodge cummins diesel engine clamp but leave it loose enough so you have a little movement to connect the other side. Then fully tighten both sides, once you have both sides lined up correctly.
14. Locate the dodge cummins diesel engine fuel pressure sensor on the back of the dodge cummins diesel engine fuel rail close to the dodge cummins diesel engine fire wall. Plug the dodge cummins diesel engine factory connector into our harness and our harness into the dodge cummins diesel engine fuel pressure sensor.
15. Connect our harness to the Diesel Performance module and mount the Diesel Performance Module in a location of your choice.
16. Mount the switch in the dodge cummins diesel engine cab any where you like.
Cummins Diesel Engine

30 day Customer Satisfaction - Dodge Cummins Diesel Engine Chips
You have 30 days to be Satisfied with the RESULTS.
LIFE TIME Warranty - Dodge Cummins Diesel Engine Chips
Dodge Cummins Diesel Engine Chips.


Need Assistance ?
Call Toll Free: 1-877-696-4370

Outside Continental US: E-mail
tsdieselperformance@gmail.com
Copyright 2016 TS Diesel Performance. Com. All material contained herein is owned by TS Diesel Performance.Com and protected. Any attempts to reproduce this information without the express written consent from the owner will be prosecuted.
TS Dodge Diesel Chips enhance Dodge Cummins Diesel Engine...
Dodge Cummins Diesel Engine works with TS Diesel Performance Chip. Dodge Diesel Chips and TS Diesel Chip is part of our Dodge Diesel performance parts inventory...
TS Diesel Chip works with the Dodge Cummins Diesel Engine...
Dodge Diesel Performance Parts & Dodge Diesel Chips increase Dodge Cummins Diesel Engine Performance. TS Diesel Performance Chip...